The following warnings occurred:
Warning [2] Undefined property: MyLanguage::$archive_pages - Line: 2 - File: printthread.php(287) : eval()'d code PHP 8.2.18 (Linux)
File Line Function
/inc/class_error.php 153 errorHandler->error
/printthread.php(287) : eval()'d code 2 errorHandler->error_callback
/printthread.php 287 eval
/printthread.php 117 printthread_multipage



Carolina Broncos
what have you wrenched on your bronco(s) today? - Printable Version

+- Carolina Broncos (https://cb4x4.com)
+-- Forum: 66-96 Ford Broncos (https://cb4x4.com/forum-7.html)
+--- Forum: Bronco Talk (https://cb4x4.com/forum-39.html)
+--- Thread: what have you wrenched on your bronco(s) today? (/thread-2701.html)



what have you wrenched on your bronco(s) today? - snipes243 - 02-03-2015

So I maxed out the highlift trying to measure for new shocks. Which I have to wait till next week to order since everyone is at KOH. [Image: af690b3cc5f5a8e1468d4490f7ebb853.jpg]

Then I got bored and dissemble the entire cage and dash. Oh fun


Sent from my iPhone using Tapatalk


what have you wrenched on your bronco(s) today? - chuzie - 02-03-2015

What, no cinder blocks laying around? Just fab up an RTI ramp!

I took a break from the Bronco today. I did start researching Odyssey batteries since my yellow top Optima is doneski. The Die Hard Platinum batteries Odyssey has been making are going to be discontinued soon so I won't be going that route for fear of warranty issues with Sears. Looks like I am going to bite the bullet and buy an Odyssey.


what have you wrenched on your bronco(s) today? - chuzie - 02-03-2015

BTW- Just noticed that wheel chock preventing your junk from rolling down the hill. NICE!!!


what have you wrenched on your bronco(s) today? - snipes243 - 02-04-2015

Safety first


Sent from my iPhone using Tapatalk


what have you wrenched on your bronco(s) today? - chuzie - 02-04-2015

Chased my unstable idle issue and intermittent low RPM stall. I suspect the TB adjustment screw may have backed itself out but still have to confirm the issue is resolved. Reset the base idle so hope all is well again.

Found I had the electric fan for my trans cooler going the wrong direction which explains why my trans temps (210) exceeded my engine temps (180). More testing tomorrow.

For fun, because I am this lame, I measured the amperage draw of my different components which are likely to be used for extended periods of time with the engine off.

Not that anyone gives a crap, but here is what I came up with:
EEC memory and radio memory 0.003 (2 years)
Battery isolation solenoid 0.720 (2 days)
Radio 6.500 (4 hours)
Dome lights 1.290 (24 hours)
Rock lights 1.000 (33 hours)
Parking lights 3.560
Head lights 8.300

Yes, I have no life!


what have you wrenched on your bronco(s) today? - jollygrngiant - 02-04-2015

Well aren't you just a little busy Bee! Must be nice to have all this free time to do odd ball testing on your bronco! ( yes, I'm jealous. Shut up)


what have you wrenched on your bronco(s) today? - chuzie - 02-05-2015

It was either that or rake leaves.

Sent from my GS3 on Cyanogenmod with the older / better version of Tapatalk!


what have you wrenched on your bronco(s) today? - chuzie - 02-08-2015

To love others, you must first learn to love yourself...

I would say I am getting pretty good at the latter. ;-)

   

Sent from my GS3 on Cyanogenmod with the older / better version of Tapatalk!


what have you wrenched on your bronco(s) today? - broncosbybart - 02-09-2015

No details needed on that Chuzie!!

Been distracted by the KOH races this week. Hadn't done much of anything


what have you wrenched on your bronco(s) today? - snipes243 - 02-09-2015

broncosbybart Wrote:No details needed on that Chuzie!!

Been distracted by the KOH races this week. Hadn't done much of anything

Same here.

Hey do you still have those stock seats I could borrow for a few days?