Carolina Broncos › 66-96 Ford Broncos › Bronco Talk v
what have you wrenched on your bronco(s) today?

Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Threaded Mode
what have you wrenched on your bronco(s) today?
firefighter2134 Offline
Posting Freak
*****
Posts: 965
Threads: 53
Joined: Nov 2009
Reputation: 0
#151
08-05-2011, 02:45 PM
ordered bushings this morning. so i will do them as soon as they come in.
If you can't fix it with a hammer and a welder then your gonna need a new one!
Find
Reply
blazinchuck Offline
Administrator
*******
Posts: 6,190
Threads: 511
Joined: Oct 2005
Reputation: 0
#152
08-08-2011, 10:44 PM
i installed a new belt tensioner hoping to eliminate a small belt squel i get anytime i rev the motor. but, doesnt look like it worked

also cleaned the Jegs fuel filter
77 built 306,Trickflow Cam/Alum Heads/dome pistons/10:1comp,nv3550,duff long arms,3.5" lift,family cage,protofab rear bumper,twin sticked, and 35KM2'sG.D.I.
Find
Reply
medwards01 Offline
Senior Member
****
Posts: 383
Threads: 24
Joined: Feb 2010
Reputation: 0
#153
08-10-2011, 12:47 AM
Dang it boy, I got an aggravating belt squeal too. Mine is more of a chirping sound as the RPMs rev up just before the C4 shifts. I been using belt dressing and with this heat wave it seems to help for about 2 days and then the chirping starts again. Belts are nice and tight, so that's not the problem....I think I'm going to bite the bullet and install new belts this weekend. The power steering belt looks kinda glazed and it's never been replaced in the 15+ years I've owned the old girl....:banghead:
Mike Edwards....74 Bronco ($ Money Pit $)
Find
Reply
firefighter2134 Offline
Posting Freak
*****
Posts: 965
Threads: 53
Joined: Nov 2009
Reputation: 0
#154
08-11-2011, 04:10 PM
my 14pc bushing kit just arrived so guess its out to the shop i go..
If you can't fix it with a hammer and a welder then your gonna need a new one!
Find
Reply
firefighter2134 Offline
Posting Freak
*****
Posts: 965
Threads: 53
Joined: Nov 2009
Reputation: 0
#155
08-11-2011, 09:51 PM
well pulled trac bar pulled and got frame up on jackstands. man the trac bar bushings were shot. guess i found the culprit of the ole death wobble.now getting ready to pull front axle. gonna go the long route to change bushings i guess. might as well weld up the carrier while i have it out from under it. spray a little krylon and put it back in. hope to be done by next weekend.
If you can't fix it with a hammer and a welder then your gonna need a new one!
Find
Reply
73Bronc Offline
Senior Member
****
Posts: 288
Threads: 29
Joined: Nov 2007
Reputation: 0
#156
08-12-2011, 12:56 AM
Pulled my oil pump. Hoping to get it replaced and reinstalled this weekend.
[SIGPIC][/SIGPIC]
Website Find
Reply
firefighter2134 Offline
Posting Freak
*****
Posts: 965
Threads: 53
Joined: Nov 2009
Reputation: 0
#157
08-15-2011, 10:29 PM
well got axle dropped on a dolly radius arms removed. ready for cleaning and bushings and paint. hope to have reinstalled by the weekend. thanks chuck for the advice!!


Attached Files Image(s)
       
If you can't fix it with a hammer and a welder then your gonna need a new one!
Find
Reply
blazinchuck Offline
Administrator
*******
Posts: 6,190
Threads: 511
Joined: Oct 2005
Reputation: 0
#158
08-16-2011, 08:58 AM
no problem, if i knew ya were doing bushings...i woulda recommended the degreed bushings from WH's...they replace those round ones at the frame. they are awesome!
77 built 306,Trickflow Cam/Alum Heads/dome pistons/10:1comp,nv3550,duff long arms,3.5" lift,family cage,protofab rear bumper,twin sticked, and 35KM2'sG.D.I.
Find
Reply
firefighter2134 Offline
Posting Freak
*****
Posts: 965
Threads: 53
Joined: Nov 2009
Reputation: 0
#159
08-16-2011, 10:28 AM (This post was last modified: 08-16-2011, 10:32 AM by firefighter2134.)
i ordered the 2 degree from duffs. i have no lift at the moment so dont need the degreed ones. but after the ure trip i plan on gathering the rest of lift parts. now im off to parts house to get brake part cleaner to clean carrier so i can weld it up then paint housing then put all back together.
If you can't fix it with a hammer and a welder then your gonna need a new one!
Find
Reply
blazinchuck Offline
Administrator
*******
Posts: 6,190
Threads: 511
Joined: Oct 2005
Reputation: 0
#160
08-16-2011, 10:38 AM
i was talking bout these, they make stock arms flex!
http://www.wildhorses4x4.com/product/Rub...d_bushings

[Image: 136_832_large.jpg]
77 built 306,Trickflow Cam/Alum Heads/dome pistons/10:1comp,nv3550,duff long arms,3.5" lift,family cage,protofab rear bumper,twin sticked, and 35KM2'sG.D.I.
Find
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Latest Bronco Driver Cameo Bronco Biff 9 3,063 05-10-2017, 11:55 PM
Last Post: snipes243
  Bronco sighting in eastern Pendleton SC Crawdad 0 1,479 01-15-2017, 10:06 AM
Last Post: Crawdad
  Bucking Bronco ParadisePWoffrD 0 847 01-18-2016, 12:18 PM
Last Post: ParadisePWoffrD
  Bronco new year resolutions wepuckett 12 2,724 01-03-2016, 11:52 AM
Last Post: Bronco Biff
  Check this bronco out snipes243 5 3,375 12-29-2015, 08:58 PM
Last Post: Bronco Biff
  Bronco Christmas snipes243 23 4,493 12-26-2015, 04:22 PM
Last Post: Bronco Biff
  Who's Charleston Bronco made my local news? Bronco Biff 0 849 10-05-2015, 08:58 AM
Last Post: Bronco Biff
  Ruff 76 I looked at today. Broncitis 20 6,082 09-05-2015, 08:49 PM
Last Post: broncosbybart
  The Bronco made the news today snipes243 8 2,068 08-24-2015, 12:45 PM
Last Post: 66Roadster
  Not a bronco but..... firefighter2134 4 1,607 07-11-2015, 10:10 PM
Last Post: firefighter2134

Forum Jump:


Users browsing this thread: 304 Guest(s)