Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
ParadisePWoffrd's EB
#61
Here is the 60F that I had been working on some too... got the 4 link brackets welded on. Working on getting the steering setup now.

I will probly put a piece of tube between the towers to truss the axle and then tie the knuckles into the truss once i figure out the shock mounting location.

   
Ben...........Big Dixie Boggers........www.MudProMetalworks.com
Reply
#62
Been busy, huh? Looking good! I probably have a spare fender or 2 that you could use to stretch your fenders with. both fenders would be damaged, but should be good enough. let me know if you want em.
Reply
#63
most of that work has been over the last little while... I managed to start widening my trailer deck too... just need to plate it.


Ill let you know... I plan to push the axle forward some when i install the 60 w/ full hydro; so I want to wait until then to make sure I dont hack away the whole fender...
Ben...........Big Dixie Boggers........www.MudProMetalworks.com
Reply
#64
Moved the gauges up into the dash, in place of the non functional heater controls...


took it out last weekend and destroyed everything but 1 stub shaft.... so, today i started the 60 swap...


Goal is to have it back together by end of the year for a new years run.... well see


also picked up a TBI setup to switch back to gasoline.... its a low priority though
Ben...........Big Dixie Boggers........www.MudProMetalworks.com
Reply
#65
you know the deal...PICS or it didnt happen lol
77 built 306,Trickflow Cam/Alum Heads/dome pistons/10:1comp,nv3550,duff long arms,3.5" lift,family cage,protofab rear bumper,twin sticked, and 35KM2'sG.D.I.
Reply
#66
Confusedtupid:
Reply
#67
haha, yeah i know... my phone isnt wanting to upload currently... ill work on that tnite
Ben...........Big Dixie Boggers........www.MudProMetalworks.com
Reply
#68
Here is a pic of the moved gauges

[Image: attachment.php?attachmentid=4929&d=1324335531]

I had some fan issues, so i relocated it to a puller and added a shroud

[Image: attachment.php?attachmentid=4928&d=1324335531]
Ben...........Big Dixie Boggers........www.MudProMetalworks.com
Reply
#69
Here are some pics of the broken shafts

[Image: attachment.php?attachmentid=4918&d=1324335029]
[Image: attachment.php?attachmentid=4919&d=1324335029]
[Image: attachment.php?attachmentid=4920&d=1324335029]
[Image: attachment.php?attachmentid=4921&d=1324335029]

so out it came

[Image: attachment.php?attachmentid=4922&d=1324335085]
Ben...........Big Dixie Boggers........www.MudProMetalworks.com
Reply
#70
Lastly, pics of the 60 swap:

it sitting under the bronco

[Image: attachment.php?attachmentid=4923&d=1324335203]

lower links (2x2x0.250)

[Image: attachment.php?attachmentid=4924&d=1324335203]

hydro mount and truss

[Image: attachment.php?attachmentid=4925&d=1324335203]
[Image: attachment.php?attachmentid=4926&d=1324335203]

5 lug hubs w/ f150 rotors

[Image: attachment.php?attachmentid=4927&d=1324335203]
Ben...........Big Dixie Boggers........www.MudProMetalworks.com
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)