Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
The Love shack
#31
:rockon: Eric, I love it when a plan comes together. The pics documenting your progress are great and the quality of your workmanship is pretty freaking awesome!! Keep those pics coming brother, you are an inspiration to us all....Can't hardly wait to see the finished product. Confusedmokin:
Mike Edwards....74 Bronco ($ Money Pit $)
Reply
#32
thanks Mike. It is kind of slow going. I have to wait on the diamond plate for the outside now. and money. im running out! should be able to tighten up the bedroom this week i hope. big wheelindixie party this weekend so I wont get anything done after friday. I hope the diamond plate works out like i hope it does.
Eric. :rebel:
Reply
#33
Awesome work my friend!!! I, like everybody else, can't wait to see it all finished!! You can tell the difference between repair and craftsmanship! We all know where your work falls!!! :xyxthumbs:
Psalms 27:1
[SIGPIC][/SIGPIC]
Reply
#34
basically what I had just about 4" higher and way sturdier.
Im just going to rebuild the little night stand things and use them. flooring and wainscoting and the bedroom is about done

[Image: repair1001.jpg]
[Image: repair1002.jpg]
[Image: repair1003.jpg]
[Image: repair1004.jpg]
[Image: repair1005.jpg]
[Image: repair1006.jpg]
[Image: repair1007.jpg]
[Image: repair1008.jpg]
[Image: repair1009.jpg]
[Image: repair1010.jpg]
[Image: repair1011.jpg]
[Image: repair1012.jpg]
[Image: repair1013.jpg]
Eric. :rebel:
Reply
#35
Looks good Eric! Keep the pics coming!:xyxthumbs:
Not a Bronco owner, but a Bronco enthusiast!

Doing big things......On leaf springs and 37's!

1984 CUCV Blazer 6.2 diesel, SM465/NP205 Dana 60, 14 bolt, detroits, recentered H1 double beadlocks, 37 inch military Goodyears.
Reply
#36
Got a ffew things done. I am just going to rebuild and reuse the night stand things for the bedroom. I got the rest of the floor done. I did the cut out and mocked up the furnace install. I was trying to make sure of the fit before i start on the kitchen and cabnets. I think im just going to build them and reuse the drawers and guides from the old stuff. the fridge and furnace area has to be sealed off from the rest of the camper because of the propane and exhaust gases. I am sheeting the wall that it goes on and also behind the counters. i had to cut the wall out on the inside to put the stringers in for the diamond plate so now that is the best way to recover that areas.

[Image: repair1101.jpg]
[Image: repair1102.jpg]
[Image: repair1103.jpg]
[Image: repair1104.jpg]
[Image: repair1105.jpg]
[Image: repair1106.jpg]
[Image: repair1107.jpg]
[Image: repair1108.jpg]
[Image: repair1109.jpg]
[Image: repair1110.jpg]
Eric. :rebel:
Reply
#37
Great job Eric. Looks like you could crash in that thing this weekend.

cw
Reply
#38
the slider is out of it and i wouldnt want to tow it there with a 5x6 hole in the side. my house is only 25 min away.
Eric. :rebel:
Reply
#39
I got the other wall fixed insulated and covered with ply. built the cabnet for the furnace access fridge, and shelf on top. it came out pretty decent.
first mistake also. i cut a 1/2 water line. cb has the crimpers for the pek stuff so its all good. sealed up most of the fridge cabnet for fumes etc . i cut out for the outside shower also.
[Image: repair1201.jpg]
[Image: repair1202.jpg]
[Image: repair1203.jpg]
[Image: repair1204.jpg]
[Image: repair1205.jpg]
[Image: repair1206.jpg]
[Image: repair1207.jpg]
[Image: repair1208.jpg]
[Image: repair1209.jpg]
[Image: repair1210.jpg]
[Image: repair1211.jpg]
[Image: repair1212.jpg]
[Image: repair1216.jpg]
[Image: repair1217.jpg]
[Image: repair1218.jpg]
[Image: repair1219.jpg]
[Image: repair1220.jpg]
Eric. :rebel:
Reply
#40
It is really coming together well Eric. Keep the pics rolling.
'74 Grocery Getter, '73 Project Buggy, '77 Parts Rig

[Image: Bannerpic.jpg]
Reply


Forum Jump:


Users browsing this thread: 2 Guest(s)