Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
trail rig!!
#11
hehe...im curious too
77 built 306,Trickflow Cam/Alum Heads/dome pistons/10:1comp,nv3550,duff long arms,3.5" lift,family cage,protofab rear bumper,twin sticked, and 35KM2'sG.D.I.
Reply
#12
well was playin in driveway after a couple cold ones and broke bolts on transfer case yoke for rear driveshaft!! better to break now than later easy fix though im ready for ure.
If you can't fix it with a hammer and a welder then your gonna need a new one!
Reply
#13
heres a snapshot of the driveshaft just hangin around...


Attached Files Image(s)
   
If you can't fix it with a hammer and a welder then your gonna need a new one!
Reply
#14
Sounds like a good ride, see ya in URE.
[SIGPIC][/SIGPIC]
Reply
#15
Luckily didn't hurt yoke or driveshaft. Got new u joint and bolts. Will have it back together tomorrow evening. im suprised it stayed together as long as it did. it had 3 mismatched bolts 2 of which were coarse thread they were only in there a turn and half...but hey i found the weakest link and will be fixed shortly
If you can't fix it with a hammer and a welder then your gonna need a new one!
Reply
#16
I have had that happen before too. It marred the pinion yoke but not enough to necessitate a replacement. I frequently check the bolts in the drive line for tightness especially before a long trip or when going off road. I also carry a spare drive shaft yoke in case it does come loose and gets jacked like it did last November at URE. I really need to carry a spare drive mshaft but don't have the $$$ for that yet.
'77 351w- Explorer EFI, 4R70W, 4-link, lockers, 4.56, 35" MT/Rs with a severe rock addiction.Confusedmokin:
Roads? Where we're going, we don't need roads.

[Image: sig2.jpg]
Reply
#17
:jump::jump:i got really lucky then cause there was no scratches on yoke whatsoever...prolly my one chance...lol but driveshaft is in new ujoint and gonna bring a couple spares to ure just n case..im used to wheeling with a 6 banger with no hp or lots of torque...so im gonna have to get used to big engine with some balls...but i also found out after i replaced bolts that i no longer have any chatter..i had some chatter when taking off in second gear but i guessing it wasnt clutch chatter but was bad u joint or loose driveshaft..problem solved now im ready to bring it !! i know the campground policy says no alcohol but what if it is kept low profile in a cup or koozie? if they are strict about it i wont bring any. dont wanna look bad for club. but its nice to unwind by a campfire with a cold one. no driving involved! :gunshot:
If you can't fix it with a hammer and a welder then your gonna need a new one!
Reply
#18
put it in a cup or a koozie and you are gold.
'77 351w- Explorer EFI, 4R70W, 4-link, lockers, 4.56, 35" MT/Rs with a severe rock addiction.Confusedmokin:
Roads? Where we're going, we don't need roads.

[Image: sig2.jpg]
Reply
#19
that is fine. thanks. look forward to meeting everybody! do i need to bring saw or anything?
If you can't fix it with a hammer and a welder then your gonna need a new one!
Reply
#20
so the trailer i had planned to pull is not wide enough so my cousin give me a trailer and i need to rewire it before sat. it is barely big enough but will work. picked up fire extinguisher for it and other than the wiring i think im ready for ure!! we will see how she holds together.
If you can't fix it with a hammer and a welder then your gonna need a new one!
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Any Interest in doing a URE trail ride Saturday the 23rd or 30th? Broncitis 24 4,528 04-27-2016, 08:46 AM
Last Post: snipes243
  How to have a successful trail ride blazinchuck 9 2,408 05-11-2015, 02:13 PM
Last Post: chuzie
  Land and trail use issue for Uwharrie- Please VOTE! broncosbybart 7 1,926 09-29-2014, 10:56 PM
Last Post: chuzie
  Adopt a trail 2014 broncosbybart 12 2,108 02-03-2014, 01:30 PM
Last Post: snipes243
  decided not to build new rig cuz1 3 1,281 10-28-2007, 08:54 AM
Last Post: cuz1

Forum Jump:


Users browsing this thread: 2 Guest(s)