Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
cooling the EB
#1
aight, a little back ground. explorer serp,explorer clutch fan, stock radiator,and 180* tstat.

sitting in traffic or cruising under 40mph the temp holds 180-185*. once i up the cruising speed to the temp goes up. on my last trip to gulches...it stayed right at 200(maybe a hair under). on the trails, it stays at 180*. just before i made the gulches trip, i installed a new clutch for the fan...but it didnt help either(which i thought it wouldnt-just wanted to confirm). i am using a stock shroud and i modified it to be closer to the fan blades. its not at or over the blades(gonna mod it some more), plus i move the rad forward a while back (if i hadnt...the shroud would be right i think.)


any thoughts?? I also bought some alum flashing to help seal up around the rad-havent done it yet.

just want to get these temps consistent before i begin swapping in AC. i know the etra load from running AC will raise the temps.
77 built 306,Trickflow Cam/Alum Heads/dome pistons/10:1comp,nv3550,duff long arms,3.5" lift,family cage,protofab rear bumper,twin sticked, and 35KM2'sG.D.I.
Reply
#2
I don't think 200 or even 210 is too hot for EFI. I haven't had my crawler at highway speeds by any means, but I can get to almost 200 idling in the garage. That's with a new Champion radiator, shroud, and explorer fan. The aux fan I have mounted on the trans cooler in front of the radiator doesn't seem to help it drop either when I cut it on. I can't remember what thermostat I put in, but I'm leaning towards 195 since it gets there and stays there. Crawling around slow and in the hot sun I get 210ish but never more than that.
'74 Grocery Getter, '73 Project Buggy, '77 Parts Rig

[Image: Bannerpic.jpg]
Reply
#3
where do you have your temp sensor? i had to drill the tstat housing to mount this mech sender...im sure thats gonna make some difference on temp readings
77 built 306,Trickflow Cam/Alum Heads/dome pistons/10:1comp,nv3550,duff long arms,3.5" lift,family cage,protofab rear bumper,twin sticked, and 35KM2'sG.D.I.
Reply
#4
The radiator shrouds make a pretty big difference
Reply
#5
I'll have to double check the location Chuck. I'll check tonight when I get home, but you are right - the T-stat housing may be one of the cooler places to check it.
'74 Grocery Getter, '73 Project Buggy, '77 Parts Rig

[Image: Bannerpic.jpg]
Reply
#6
Roberts right, 200,210 is not too high a temp. Most ecms want to see 195 before it will run in closed loop. But with the ac it may go up from there. If it does it definetly sounds like a lack of air flow at higher rpms. You could counter this with a lower t-stat(I run a 160) or play with the fan shroud some. I'm guessing you dont have room for an aux fan. So how about an oil cooler. I was able to realy stablaize my temps with a remote oil filter housing and oil cooler. Shouldent your intake have had a bung for the temp sensor?
[SIGPIC][/SIGPIC]
Reply
#7
it does have 1 bung ,thats for the computer harness temp sensor...no room for my mech gauge
77 built 306,Trickflow Cam/Alum Heads/dome pistons/10:1comp,nv3550,duff long arms,3.5" lift,family cage,protofab rear bumper,twin sticked, and 35KM2'sG.D.I.
Reply
#8
Ok, I got ya. To compare gauges put a scan tool or code reader on it in moniter mode. But I bet you will be ok for now. I would probably wait and compare the gauges before I made too many changes.
[SIGPIC][/SIGPIC]
Reply
#9
i know 200 is not high...im trying to stabilize it. when i put this motor in and the 5.0 stang motor...i used a 195* both times. i wanted to see how bad things would get running the right tstat. well, with the mustang serp/fix fan...it was stable. switched to explorer serp and it stay at 200-then went to 205-210* on highway. so a couple weeks ago while trying the explorer radiator...i swapped in a 180*fail-safe stat. now like i said the temp holds 180-185* in any traffic jam at any temp outside(thats great!) but i dont like how i cant seem to control it going to 200* on the highway(once in a while at hi speeds...205*) once i come back to normal traffic...it takes a long time to come down to normal temps. also this motor was treated to a new explorer water pump. i sure the radiator needs a good flushing(not like i do...but i service place)
77 built 306,Trickflow Cam/Alum Heads/dome pistons/10:1comp,nv3550,duff long arms,3.5" lift,family cage,protofab rear bumper,twin sticked, and 35KM2'sG.D.I.
Reply
#10
My mech gauge reads from a bung on the driver side of the intake. The ECM temp sensor plugs into the hard coolant line that runs between the upper and lower intakes on the pass. Side.
Reply


Forum Jump:


Users browsing this thread: 2 Guest(s)