|
4 speed tranny, will it work on EB
|
I'm looking at getting a NP435 (don't need it, but want it?!!!!) and I want to know if this one will work for me. I'm still getting info on it, will post more later.
[SIZE="2"]77 project bronco w/ 5.0 & c4, Sagi PS, 2 hard tops, eyebrow grill [/SIZE]
WANTED: auto column, gas tank, front/ rear seats 
08-10-2011, 12:36 PM
The 435 will bolt in place of the stock 3 spd. Some modifications may be needed. Realy depends on what its out of. But overall it should work.
[SIGPIC][/SIGPIC]
08-10-2011, 12:42 PM
broncomatt Wrote:The 435 will bolt in place of the stock 3 spd. Some modifications may be needed. Realy depends on what its out of. But overall it should work. Thx Matt, Would the bellhousing from a three speed work for a NP435 4-spd?
[SIZE="2"]77 project bronco w/ 5.0 & c4, Sagi PS, 2 hard tops, eyebrow grill [/SIZE]
WANTED: auto column, gas tank, front/ rear seats 
08-10-2011, 12:50 PM
as long as the tranny has a square bolt battern rather than the trapezoid pattern
If you can't fix it with a hammer and a welder then your gonna need a new one!
08-10-2011, 07:50 PM
The owner tells me the tranny is from a Ford F-250 2wd. Does not have bellhousing or linkages. 10 spline in front, 28 spline in rear. He said his 3 speed bellhousing doesn't fit the NP435.
[SIZE="2"]77 project bronco w/ 5.0 & c4, Sagi PS, 2 hard tops, eyebrow grill [/SIZE]
WANTED: auto column, gas tank, front/ rear seats
08-10-2011, 11:34 PM
if the np435 has the square bolt pattern then it should be the same as the stock
If you can't fix it with a hammer and a welder then your gonna need a new one!
08-11-2011, 01:25 PM
I'm going to look at it this weekend, will let you know. Such a good deal it is hard to pass up even if I don't have all the parts. I may just sit on it for a while.
[SIZE="2"]77 project bronco w/ 5.0 & c4, Sagi PS, 2 hard tops, eyebrow grill [/SIZE]
WANTED: auto column, gas tank, front/ rear seats
08-11-2011, 01:33 PM
worse case just have to find a trap. bell housing. but i love the 435 swap i done. not really different on highway but super low first and reverse. cant wait to test it off road
If you can't fix it with a hammer and a welder then your gonna need a new one!
08-12-2011, 08:23 PM
the 3sp bellhousing should work, and what Asiel said(square bolt pattern-not trapezoid)this pattern is the tail shaft side.
you still need an adapter 1" thick. AA makes a intermediate housing(goes between tranny and T-case) that had the 1" adapter built into the intermediate housing(very pricey though) when i did mine i looked around and bought one (1" adapter) from ebay...bout $100
77 built 306,Trickflow Cam/Alum Heads/dome pistons/10:1comp,nv3550,duff long arms,3.5" lift,family cage,protofab rear bumper,twin sticked, and 35KM2'sG.D.I.
08-12-2011, 08:55 PM
1" adapter with a 6cyl housing(this makes it a simple swap) no need to move cross member
77 built 306,Trickflow Cam/Alum Heads/dome pistons/10:1comp,nv3550,duff long arms,3.5" lift,family cage,protofab rear bumper,twin sticked, and 35KM2'sG.D.I.
|
|
« Next Oldest | Next Newest »
|
| Possibly Related Threads… | |||||
| Thread | Author | Replies | Views | Last Post | |
| who does your fab work? | c-dub | 1 | 1,009 |
08-21-2011, 10:44 PM Last Post: broncosbybart |
|
| any tranny shops round fayetteville? | c-dub | 1 | 1,091 |
05-29-2010, 01:20 AM Last Post: c-dub |
|
| Done some work on the Bronco .... | Mill Knob | 36 | 6,944 |
09-26-2009, 11:07 PM Last Post: Mill Knob |
|
| Tranny swap | Nathan Mattar | 7 | 2,888 |
11-20-2008, 08:16 PM Last Post: Jabo76 |
|
| New Roll cage, tranny, sliders and fab front bumber | johnpaulgolf | 151 | 19,185 |
06-27-2008, 04:12 PM Last Post: johnpaulgolf |
|
| ZF 5-speed? | blazinchuck | 2 | 1,781 |
05-23-2008, 05:49 PM Last Post: Bighorn |
|
| I actuly got to work on my eb | broncomatt | 1 | 1,143 |
02-15-2008, 05:48 PM Last Post: cuz1 |
|
| Tranny is in!!! | NC-Fordguy | 2 | 909 |
01-17-2008, 05:59 AM Last Post: blazinchuck |
|
