Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
1990 Bronco Front Locking Hub Question
#1
We just replace out automatic hubs with locking hubs and the one hub seam a little loose, all the bolts are tight but it has a little wiggle in it. Is this ok or do i need to shim somthing?Confusedcratchhe:

Thanks, JOhn
Reply
#2
All thrush washers installed in right place? Bearing pre-load the same? Weak spring? Could be a lot of things!! :xyxthumbs:
Psalms 27:1
[SIGPIC][/SIGPIC]
Reply
#3
Not really sure about washer or springs. We got the truck back from East Coast Gear last month after installing gears and they replaced the hub to manual hub for us. When i say movement I mean a LITTLE movement. Is a little movement bad???

Thanks
Reply
#4
F1504x2 Wrote:Not really sure about washer or springs. We got the truck back from East Coast Gear last month after installing gears and they replaced the hub to manual hub for us. When i say movement I mean a LITTLE movement. Is a little movement bad???

Thanks

Mine doesn't move or wiggle at all. I'm not sure if "a little" is ok. Someone will tell you just be patient. :xyxthumbs:
Psalms 27:1
[SIGPIC][/SIGPIC]
Reply
#5
there shouldnt be any play in a locking hub cuz it will let water in and mud or it can cuz it to fail on u while on the trails is it just one side
GO BIG OR GO HOME!!!
Reply
#6
Just one side and it's a only a small wiggle, i have pulled it off it still clean and dry and it's been like this for the past 4-6 weeks.Confusedcratchhe:
Reply
#7
I don't like the sounds of that... It's normally just the opposite.. you have to push the outer axle out to get the locknut on all the way... I'd definitely give chase (ECGS) a call... if it's wrong, he'll make it right!
Reply
#8
definetly take it back, if there is play in there it indicates a loose component. Posibly an incorrect spring or a missing part. Water will certanly get in there if you wheel like that.
New hubs should be super tight, some times they even feel to tight.
I would give them a call.
Broncomatt
[SIGPIC][/SIGPIC]
Reply
#9
Any one have an exploded view of all item in the hub so i can check to make sure nothing is missing?

Thanks
Reply
#10
F1504x2 Wrote:Any one have an exploded view of all item in the hub so i can check to make sure nothing is missing?

Thanks

Let me dig one up, if I don't already have it.... I'll post it up later today.
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  1996 Ford Bronco- Body Bushing Install jrshepherd 2 2,435 09-19-2018, 02:50 PM
Last Post: blazinchuck
  Stainless/ Coated Headers needed- 1995 Bronco 351 Windsor .20 over trick flow heads jrshepherd 1 3,251 05-22-2018, 09:38 PM
Last Post: broncosbybart
  Locking Hubs?? Whats the best??? Broncitis 9 6,735 02-26-2017, 01:51 PM
Last Post: snipes243
  1977 Ford Bronco rear ended 9" rebuild Crawdad 10 5,208 01-19-2017, 12:53 PM
Last Post: snipes243
  BC Bronco Soft Top knoxville714 3 3,158 07-12-2016, 08:04 PM
Last Post: blazinchuck
  1996 Bronco New BSD 4" long arm lift on IFS suspension- Setting Wheelbase jrshepherd 11 3,830 01-31-2016, 03:55 PM
Last Post: broncosbybart
  Steering shaft Extension Question??? Broncitis 4 2,882 04-17-2015, 02:27 PM
Last Post: Broncitis
  Front shock mounts snipes243 14 4,001 03-01-2015, 07:51 PM
Last Post: scbronco
  Another Bronco Floor Replacement jdowns67 83 14,602 12-20-2014, 11:33 AM
Last Post: jdowns67
  Exhaust question Casey835 27 7,295 08-16-2013, 06:03 PM
Last Post: blazinchuck

Forum Jump:


Users browsing this thread: 1 Guest(s)