Carolina Broncos › 66-96 Ford Broncos › Bronco Tech v
PCV Grommet 1996 5.8L

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Threaded Mode
PCV Grommet 1996 5.8L
jrshepherd Offline
Member
***
Posts: 85
Threads: 34
Joined: Mar 2009
Reputation: 0
#1
01-03-2011, 04:08 PM
Im having a lot of trouble removing the PCV grommet on my 1996 5.8L. I can't see the round elbow, and I can't twist it out. Does anyone know how to remove the grommet? Thanks again:banghead:
Find
Reply
blazinchuck Offline
Administrator
*******
Posts: 6,190
Threads: 511
Joined: Oct 2005
Reputation: 0
#2
01-03-2011, 04:28 PM
it should just twist out once you remove the PCV valve...heres a pic that might help with what you can see
[Image: pcv937_full.jpg]
77 built 306,Trickflow Cam/Alum Heads/dome pistons/10:1comp,nv3550,duff long arms,3.5" lift,family cage,protofab rear bumper,twin sticked, and 35KM2'sG.D.I.
Find
Reply
blazinchuck Offline
Administrator
*******
Posts: 6,190
Threads: 511
Joined: Oct 2005
Reputation: 0
#3
01-03-2011, 04:30 PM
also a flat screw driver can be pretty handy getting under the outside lip, then lift up and twist out,HTH
77 built 306,Trickflow Cam/Alum Heads/dome pistons/10:1comp,nv3550,duff long arms,3.5" lift,family cage,protofab rear bumper,twin sticked, and 35KM2'sG.D.I.
Find
Reply
jrshepherd Offline
Member
***
Posts: 85
Threads: 34
Joined: Mar 2009
Reputation: 0
#4
01-03-2011, 04:41 PM
I thought so, but the pcv valve sit's up near the firewall. There is the grommet, elbow (Round hard plastic), house to PCV and then the PCV to intake manfold. Everything is out except the grommett and round elbow (hard plastic). Thanks for the pic?
Find
Reply
blazinchuck Offline
Administrator
*******
Posts: 6,190
Threads: 511
Joined: Oct 2005
Reputation: 0
#5
01-03-2011, 04:47 PM
well, if your gonna replace it anyway...just take a razor blade to trim the grommet down some or slice it a little...so it will release the elbow and then the grommet can come out
77 built 306,Trickflow Cam/Alum Heads/dome pistons/10:1comp,nv3550,duff long arms,3.5" lift,family cage,protofab rear bumper,twin sticked, and 35KM2'sG.D.I.
Find
Reply
jrshepherd Offline
Member
***
Posts: 85
Threads: 34
Joined: Mar 2009
Reputation: 0
#6
01-03-2011, 11:14 PM
I wish I could. It can't be cut with a razor blade. The elbow part is round plastic not rubber. I think it is only on the 5.8L. thanks!
Find
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  1996 Ford Bronco- Body Bushing Install jrshepherd 2 2,411 09-19-2018, 02:50 PM
Last Post: blazinchuck
  1996 Bronco New BSD 4" long arm lift on IFS suspension- Setting Wheelbase jrshepherd 11 3,813 01-31-2016, 03:55 PM
Last Post: broncosbybart
  1996 5.8 L Engine Rebuild- Cylinder heads jrshepherd 0 2,581 07-17-2011, 11:13 AM
Last Post: jrshepherd
  Engine Rebuild. 1996 5.8 L jrshepherd 0 985 05-05-2011, 02:02 AM
Last Post: jrshepherd
  1996 5.8L spark plug wires and coil jrshepherd 0 1,020 02-08-2011, 06:16 PM
Last Post: jrshepherd
  Changing spark plugs 1996 5.8L jrshepherd 0 847 12-13-2010, 10:42 PM
Last Post: jrshepherd

Forum Jump:


Users browsing this thread: 1 Guest(s)