Carolina Broncos › 66-96 Ford Broncos › Bronco Tech v
rear axle shims?

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Threaded Mode
rear axle shims?
berg bronco Offline
Senior Member
****
Posts: 646
Threads: 43
Joined: Nov 2008
Reputation: 0
#1
01-03-2011, 07:33 PM
are they neccessary? i had a local mechanic tell me that i need them! i have a 3.5 inch lift with 11 pack leaf springs with no blocks. if they are needed what degree shim would be the best?
Life is short------drive your bronco everyday!
Find
Reply
blazinchuck Offline
Administrator
*******
Posts: 6,190
Threads: 511
Joined: Oct 2005
Reputation: 0
#2
01-03-2011, 07:51 PM
well, most nice leafs will have that built in. it is necessary-because you have to keep the pinion at the right angle to the transfer case. usually about 1-2 degrees under inline with the driveshaft. with all this said...you might have to install the leafs first then,check how much of a degree shime you will need. I didnt have to run any with my BCBronco 11 leafs,HTH
77 built 306,Trickflow Cam/Alum Heads/dome pistons/10:1comp,nv3550,duff long arms,3.5" lift,family cage,protofab rear bumper,twin sticked, and 35KM2'sG.D.I.
Find
Reply
berg bronco Offline
Senior Member
****
Posts: 646
Threads: 43
Joined: Nov 2008
Reputation: 0
#3
01-03-2011, 08:32 PM
i have wild horses 11pack with the 3.5 lift built in. theve been on the truck for 6 months and i havent had any trouble. how do i check the the angle?
Life is short------drive your bronco everyday!
Find
Reply
Timstrk Offline
Senior Member
****
Posts: 402
Threads: 38
Joined: Feb 2006
Reputation: 0
#4
01-03-2011, 09:26 PM
The driveshaft and the pinion shaft should be in a straigh line. If not the u-joint wil accelerate in part of its rotation and decel on another part. It will wear the joint out doing this. Closer to straight is better. Actually straight is best. Use a tubing bender mag base angle finder. Put it on the top of your drive shaft and then on top of the pinion guard. The two should have the same deflection off "0" or be at the same angle from 90 degrees.

Tim
74 Bronco Ranger halfcab w/toys: lockers f&r, wristed arm, C4, D20, hyd assist steering, 37"MTRs, warm 302. Capability, that's what I'm talkin' bout.
[Image: 2rwp56f.png]
Find
Reply
Crawdad Offline
Posting Freak
*****
Posts: 1,252
Threads: 77
Joined: Nov 2010
Reputation: 0
#5
01-03-2011, 10:06 PM
I bought a 4" rear lift from JBG (either 5 or 6 pack) and I asked them if I needed shims and they said they do not run shims on their lifts of that size. I still think I need shims.
[SIZE="2"]77 project bronco w/ 5.0 & c4, Sagi PS, 2 hard tops, eyebrow grill [/SIZE]
WANTED: auto column, gas tank, front/ rear seats
Find
Reply
broncosbybart Offline
Moderator
*****
Posts: 3,290
Threads: 141
Joined: Dec 2007
Reputation: 0
#6
01-03-2011, 11:15 PM
I hadn't needed to run shims on any of the 10 or 11 pack springs that I've installed. Can you post pics of what it looks like?
Find
Reply
chuzie Offline
Administrator
*******
Posts: 4,530
Threads: 131
Joined: Nov 2005
Reputation: 0
#7
01-04-2011, 12:04 AM
The beauty of a 4-link is being abe to dial in the pinion angle. Smile
'77 351w- Explorer EFI, 4R70W, 4-link, lockers, 4.56, 35" MT/Rs with a severe rock addiction.Confusedmokin:
Roads? Where we're going, we don't need roads.

[Image: sig2.jpg]
Website Find
Reply
berg bronco Offline
Senior Member
****
Posts: 646
Threads: 43
Joined: Nov 2008
Reputation: 0
#8
01-04-2011, 12:08 AM
broncosbybart Wrote:I hadn't needed to run shims on any of the 10 or 11 pack springs that I've installed. Can you post pics of what it looks like?

ya ill get some in the a.m.
Life is short------drive your bronco everyday!
Find
Reply
berg bronco Offline
Senior Member
****
Posts: 646
Threads: 43
Joined: Nov 2008
Reputation: 0
#9
01-04-2011, 12:12 AM
chuzie Wrote:The beauty of a 4-link is being abe to dial in the pinion angle. Smile

bieng you and Chuck are so good at the install you guys can come install the 4link for me!:xyxthumbs: perfect getaway to the mountians.
Life is short------drive your bronco everyday!
Find
Reply
berg bronco Offline
Senior Member
****
Posts: 646
Threads: 43
Joined: Nov 2008
Reputation: 0
#10
01-04-2011, 08:52 PM
[Image: DSC_3921640x480.jpg]


[Image: DSC_3920640x480.jpg]
heres a few pics
Life is short------drive your bronco everyday!
Find
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  1977 Ford Bronco rear ended 9" rebuild Crawdad 10 5,167 01-19-2017, 12:53 PM
Last Post: snipes243
  Rebuilding used rear leaf springs Crawdad 5 4,293 12-12-2016, 11:54 AM
Last Post: Crawdad
  Lighted rear view mirror chuzie 6 4,723 06-20-2015, 12:18 AM
Last Post: chuzie
  rear main seal snipes243 5 2,986 05-03-2014, 11:45 AM
Last Post: chuzie
  stock rear drums scbronco 11 2,624 03-06-2014, 08:09 PM
Last Post: Bronco Biff
  Late 70s Cadi rear disc brakes for 77 banjo rear end Crawdad 11 3,887 01-11-2014, 12:26 AM
Last Post: Crawdad
  77 EB Rear Drive Shaft Dropped - Second time in six months UTFLIWGYA 4 2,042 12-01-2013, 10:38 PM
Last Post: broncomatt
  Axle Tube Vents Casey835 4 1,432 03-01-2013, 08:20 PM
Last Post: Casey835
  Grinding sound from rear end area when driving Crawdad 10 4,490 02-09-2013, 09:33 PM
Last Post: blazinchuck
  '94 351 Rear Main replacement JayT 5 1,657 12-22-2012, 05:34 PM
Last Post: JayT

Forum Jump:


Users browsing this thread: 1 Guest(s)